FTM-7250DR FCC Certification

Whisky Kadman | marzo 21, 2018

FTM-7250DR FCC Certification

Federal Communications Commission Authorization and Evaluation Division

FTM-7250DR

A. Part 15.19 & 15.21 Compliance Statement Drawing:

l. Changes or modifications to this device not expressly approved YAESU MUSEN could void the user’s authorization to operate this device.

2. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) this device must accept any interference including interference that may cause undesired operation.

3. The scanning receiver in this equipment is incapable of tuning, or readily being

altered, by the user to operate within the frequency bands allocated to the Domestic public Cellular Telecommunications Service in the Part 22.

B. Part 15.19 & 15.21 Compliance Statement Drawing Location: IN Operating Manual

GENERAL INFORMATION

EUT Description	VHF/ UHF DIGITAL/ ANALOG SCANNING RECEIVER
Model Number	FTM-7250DR
Range	108 – 580 MHz
Receiver Circuit Type	Superheterodyne
Lowest I nternal Frequency	16 MHz
2^nd Harmonic of Highest Tuned Frequency	1160 MHz
Antenna Connector	UHF
EUT Power Source	110-120Vac/50- 60Hz
	13.8 VDC Nominal (Optional)
	Battery Operated Exclusively
Test Item	Prototype
	Pre-Production
	Production
Modifications required for Testing	None
Test Site	Timco Engineering, Inc. 849 NW State Road 45 Newberry, FL 32669 Designation #: US1070

REPORT SUMMARY

Regulatory Standard	CFR Title 47 FCC Rule part 15B § 15.109, 15.111, & 15.121
Test Procedures	FCC Part 15.31, 15.33, 15.35 ANSI C63.4 – 2014
Operational Modes	Stopped at the Lowest, middle, and highest frequency of each frequency range. In addition, scanning all frequencies of tuning range.
	Low: 108 MHz
Test Frequencies	Middle: 344 MHz
Test Frequencies	High: 580 MHz
	Scan: 108 kHz to 580 MHz
Environmental Condition in the laboratory	Temperature: 24-26°C Relative humidity: 50-65% Barometric Pressure: 1021 mb
Deviation from the standard/ procedure	No deviation

RADIATED SPURIOUS EMISSIONS

Rule Part No.: FCC Part 15 Subpart B, RSS-215 sec 5.1

Requirements: FCC Part 15.109(a), RSS GEN 7.1.2 Radiated Emission Limit

Class B Field Strength Limits @ 3 Meters
Frequency		Level
(MHz)		(dBuV/ m)
30 – 88		40.0
80 – 216		43.5
216 – 960		46.0
Above 960		54.0
	FCC Part 15.109(f) Radiated Emission Limit For a receiver which employs terminals for the connection of an external receiving antenna, the receiver shall be tested to demonstrate compliance with the provisions of this section with an antenna connected to the antenna terminals unless the antenna conducted power is measured as specified in §15.111 (a).
Procedure:	FCC Part 15.33(b)(3) Freauency range of radiated measurements FCC Part 15.35(a) Measurement detector functions and bandwidths ANSI C63.4 Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Eauipment 9 kHz to 40 GHz
	§ 6.2 Operating conditions § 6.3 Arrangement of EUT§ 8.3.1 Exploratory radiated emissions measurements § 8.3.2 Final radiated emission measurements
Configuration:	The scanner receiver spurious emissions are to be measured when the receiver is in the scanning mode and repeated when the scanning is stopped, all while the antenna terminals are terminated into a non- radiating 50 Ohm. load.